Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Ultramid® B3WG6 GPX BK23238 - PA6-GF30 - BASF

Check here, which other Ultramid B datasheets, application examples or technical articles are available in Material Data Center

Processing/Physical Characteristics - 기계적 특성 - 열적 특성 - 전기적 특성 - 기타 특성 - 물질의 비성질 - Processing Recommendation Injection Molding - 도표

Any use of this information falls under the rules of our disclaimer.

제품 설명서

Glass fibre reinforced and heat ageing resistant injection moulding grade for primary use in plastic air intake manifolds.
This grade has been engineered to provide excellent long-term burst strength retention.

Processing/Physical Characteristics	건조/응축	단위	시험규격
ISO 데이터
용융 부피 - 흐름 속도, MVR	20 / *	cm³/10min	ISO 1133
온도	275 / *	°C	-
하중	5 / *	kg	-
성형 수축률, 평행	0.3 / *	%	ISO 294-4, 2577
성형 수축률, 수직	0.6 / *	%	ISO 294-4, 2577

기계적 특성	건조/응축	단위	시험규격
ISO 데이터
인장탄성률	9800 / 5400	MPa	ISO 527
파단시 강도	185 / 110	MPa	ISO 527
파단시 신율	3.5 / 8	%	ISO 527
탄성변형률, 1000h	* / 4100	MPa	ISO 899-1
챠피 충격 강도 , +23°C	95 / 105	kJ/m²	ISO 179/1eU
챠피 충격 강도, -30°C	85 / 95	kJ/m²	ISO 179/1eU
챠피 노치드 충격 강도, +23°C	13 / 22	kJ/m²	ISO 179/1eA
챠피 노치드 충격 강도, -30°C	10 / 11	kJ/m²	ISO 179/1eA

열적 특성	건조/응축	단위	시험규격
ISO 데이터
녹는점, 10°C/min	220 / *	°C	ISO 11357-1/-3
하중하에서의 변형온도, 1.80 MPa	200 / *	°C	ISO 75-1/-2
하중하에서의 변형온도, 0.45 MPa	220 / *	°C	ISO 75-1/-2

전기적 특성	건조/응축	단위	시험규격
ISO 데이터
상대 유전율, 100Hz	4.6 / 33.4	-	IEC 62631-2-1
상대 유전뮬, 1MHz	4.1 / 5.4	-	IEC 62631-2-1
소산 인자, 100Hz	126 / 8930	E-4	IEC 62631-2-1
소산 인자, 1MHz	201 / 1340	E-4	IEC 62631-2-1
부피 저항	1.1E9 / 1.3E8	Ohm*m	IEC 62631-3-1
표면 저항	* / 5.2E12	Ohm	IEC 62631-3-2
전기 압력	47 / 29	kV/mm	IEC 60243-1
CTI	375 / 375	-	IEC 60112

기타 특성	건조/응축	단위	시험규격
물에서의 흡수성	6.6 / *	%	ISO 62와 유사
조건에서의 흡습성	2.35 / *	%	ISO 62와 유사
밀도	1350 / -	kg/m³	ISO 1183

물질의 비성질	건조/응축	단위	시험규격
ISO 데이터
점도수	150 / *	cm³/g	ISO 307, 1157, 1628

Processing Recommendation Injection Molding	값	단위	시험규격
Pre-drying - Temperature	80	°C	-
Pre-drying - Time	4	h	-
Processing humidity	≤0.15	%	-
용융수지온도	270 - 290	°C	-
성형온도	80 - 90	°C	-

도표

특징

생산 공정

사출 성형

인도 유형

검정

지역별 검색

쨘횕쩐횈쨍횧쨍짰횆짬, 짱쨌쨈, 쩐횈쩍횄쩐횈 횇횂횈챵쩐챌 횁철쩔짧, 쨀짼쨘횓 쨔횞 횁횩쩐횙 쩐횈쨍횧쨍짰횆짬, 쨉쩔쩐챌 쨔횞 쩐횈횉횁쨍짰횆짬 짹횢쩔짧

기타 정보

사E성

PREPROCESSING
Pre/Post-processing, max. allowed water content: .15 %
Pre/Post-processing, Pre-drying, Temperature: 80 °C
Pre/Post-processing, Pre-drying, Time: 4 h

PROCESSING
injection molding, Melt temperature, range: 270 - 290 °C
injection molding, Melt temperature, recommended: 280 °C
injection molding, Mold temperature, range: 80 - 90 °C
injection molding, Mold temperature, recommended: 80 °C
injection molding, Dwell time, thermoplastics: 10 min

Disclaimer

Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.

Created: Source: www.materialdatacenter.com

Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.